H2O Labs Water Distiller for Water Quality Testing

This H2O Labs Water Distiller is an intelligent distillation processing device that integrates constant temperature heating, automatic control of the distillation end point, and cooling water circulation according to laboratory distillation pretreatment operating procedures. It applies to places where various chemical laboratories such as environmental protection, disease control, aquatic products, water supply and drainage, universities, research institutes, factories, and mining enterprises need distillation treatment. It is easy to use, energy saving, and environmental protection.

The features of the H2O Labs Water Distiller:

1. The heating module adopts a far-infrared ceramic furnace with heating power adjustment and thermal radiation.
2. High distillation speed and long service life;
3. A weighing pressure sensor's distilling endpoint controls the automatic stop-locking function. We can set the distilling volume and weight at will to stop heating automatically.
4. The closed internal circulation reflux system is adopted for cooling without an external cooling water source. The compressor refrigeration+air cooling double refrigeration cooling cycle system is equipped, which is suitable for mass work and has a good condensation effect!
5. Set up an anti-vacuum electronic valve, with anti back suction function, without a manual guard!

Main Technical Data for the H2O Labs Water Distiller:

1. Heating method: far infrared ceramic heating furnace is used for infrared radiation heating (no open flame heating, waterproof), and a thermal insulation system is configured for heat loss so that the sample is heated more evenly.

2. Heating unit: 6 or 4, single hole and single control;

3. Heating time: 5-8 min;

4. Distillation speed: 12ml/min;

5. Distillation endpoint control: automatic detection of distillation end point function, dual power of pressure sensing and time, distillation volume 1-500ml ± 2ml, light alarm after distillation, high degree of automation;

6. Single furnace heating power: 100W-800W (single hole adjustable);

7. Large heating power: 2400W-4800W (adjustable);

8. Refrigeration power: input power ≤ 800W, refrigeration power ≥ 2000W;

9. Cooling mode of integrated multi-function distiller manufacturer: closed internal circulation reflux system, built-in compressor refrigeration, and air cooling, no external cooling water source is required, and the cooling area and heating area are separated for good refrigeration effect, and convenient for cleaning;

10. Anti-back suction: anti-vacuum solenoid valve with anti-back suction function;

11. Receiving device: the default configuration is that the volumetric flask can be received by changing other containers according to the experimental requirements, and the tray can be flexibly configured;

12. Time control: 0-200min adjustable;

13. Distillation bottle specification: 500mlX6/250 X6 or 500mlX4/250 X4

14. Rated voltage/frequency: 220V/50HZ;

15. Overall dimension: 900mm * 450mm * 800mm;

The following are precautions for the use of H2O Labs Water Distiller:

1. When we use the instrument for the first time, it is recommended to use pure or distilled water to prevent scale formation. Add the liquid level to the red mark line of the liquid level window, which can be recycled for over half a year. If the fluid level is lower than the yellow line and the cooling effect is poor, add less water than the red mark line.

2. The connection between the distillation bottle and the condensate bottle is well sealed, and the sealing plug at the top of the distillation bottle is effectively connected with the solenoid valve through the hose to prevent air leakage. During the experiment, putting other sundries near the tray is prohibited to avoid affecting the accuracy of weighing.

3. The cooling effect will decline when the room temperature exceeds 25 ℃ in summer. When the room temperature is lower than 0 ℃ in winter, it is necessary to do an excellent job of cold protection and warmth preservation of the instrument to prevent the cracking of the condensing device from making it unusable. Connecting a supporting cooling device or tap water for cooling is recommended.

4. The measuring range of the load cell is 3 kg. If necessary, please use the time control mode. For two consecutive distillation experiments, the switch of cold water circulation shall be open after the first test to ensure the condensation effect.